General Purpose, 1 Form A, Solid State Relay (Photo MOSFET), 400V/0.12A/25ohm

The ASSR-41XX Solid State Relay (SSR) series uses an AlGaAs infrared light-emitting diode (LED) input stage optically coupled to a high-voltage output detector circuit. The detector consists of a high-speed photovoltaic diode array and driver circuitry to switch on/off two discrete high voltage MOSFETs. The relay turns on (contact closes) with a minimum input current of 3mA through the input LED. The relay turns off (contact opens) with an input voltage of 0.8V or less.

The single channel configurations, ASSR-4110 and ASSR-4111, are equivalent to 1 Form A Electromechanical Relays (EMR), and the dual channel configuration, ASSR-4120, is equivalent to 2 Form A EMR. They are available in 4-pin SO, 6-pin DIP, 8-pin DIP and Gull Wing Surface Mount for DIP packages. Their electrical and switching characteristics are specified over the temperature range of -40°C to 85°C. They are used for general purpose switching of signals and low power AC/DC loads.

ASSR-4111 enables AC/DC and DC-only output connections. For DC-only connection, the output current, I_o, increases to 0.24A and the on-resistance, R_(ON) reduces 8.5Ω.

 

Check Distributor Inventory

Lifecycle status:Active

• Compact Solid-State Bi-directional Signal Switch
• Single and Dual Channel Normally-off Single-Pole-Single-Throw (SPST) Relay
• 400V Output Withstand Voltage
• 0.12A Current Rating or 0.24A Current Rating (See Schematic for ASSR-4111 Connections A & B)
• Low Input Current: CMOS Compatibility
• Low On-Resistance: 5 Ω Typical for DC only, 16 Ω Typical for AC/DC
• Very High Output Off-state Impedance: 10 Teraohms Typical
• High Speed Switching: 0.1ms (Ton), 0.02ms (Toff) Typical
• High Transient Immunity: >1kV/µs
• High Input-to-Output Insulation Voltage
  (Safety and Regulatory Approvals Pending)
  - 3750 Vrms for 1 min per UL1577
  - CSA Component Acceptance
• Options available are:
  ASSR-4110
  50XE = Tape and Reel Packaging Option
  XXXE = Lead-Free Option

ASSR-4111 and ASSR-4120
30XE = Gull Wing Option
50XE = Tape and Reel Packaging Option
XXXE = Lead-Free Option

• Telecommunication Switching
• Data Communications
• Industrial Controls
• Medical
• Security
• EMR / Reed Relay Replacement

Data Sheets & Technical Specifications

• Data Sheet - ASSR-4110, ASSR-4111 and ASSR-4120 General Purpose, Form A, Solid State Relay (Photo MOSFET) (400V/0.12A/25Ω)(424 KB,PDF)
• Options Data Sheet - Option 020 Optocoupler Option for 5000 V rms 1 Minute Requirement(85 KB,PDF)
• Options Data Sheet - Option 060 IEC EN DIN EN 6074752 Option for Plastic Optocouplers(86 KB,PDF)
• Options Data Sheet - Option 300, Gull Wing Surface Mount Option for Optocouplers(99 KB,PDF)
• Options Data Sheet - Option 500 - Tape and Reel Packaging Option for Optocouplers(93 KB,PDF)
• Options Data Sheet - Shipping Tube Dimension for Optocouplers (Plastic/Solid State Relay)(141 KB,PDF)
• White Paper - Optocouplers in Industrial Communication(277 KB,PDF)
• White Paper - Solid State Relay Transient Immunity(124 KB,PDF)

Application Notes

• Application Note - AN 5302 - Solid State Relay, ASSR Series Input Control Drive and Various Loads(212 KB,PDF)
• Application Note - AN 5452; Design Considerations for Solid State Relays(157 KB,PDF)
• Application Note - AN 5456; Dynamic Power Dissipation Considerations for Solid State Relays(105 KB,PDF)
• Application Note - AN 5476; Recommended Soldering Profile for Lead-Free Plastic Optocouplers and Solid State Relays(98 KB,PDF)

Product Change Notices

• Product Changes Notice (PCN) - PCN: V07-003-32002150-0A, Apr. 2007(19 KB,PDF)

Quality & Reliability

• Regulatory Certificate - Avago Regulatory Guide to Isolation Circuits(558 KB,PDF)